Ready-to-use, water-based, elastic, waterproofing mastic compound. It is used for effective waterproofing on the surfaces of walls, floors and ceilings in premises with periodic wetting (sanitary conveniences, bathrooms, and shower rooms, corridors, kitchens and balconies).
ADVANTAGES
- Keeps high adhesion to mineral lower stratums (concrete, plaster, brick, etc.), as well as to gypsum plasterboard and technical types of plastic
- Keeps high elasticity over the entire service life, bridge up cracks up to 2 mm * formed in the lower stratum
- It is easily and conveniently applied by brush, roller, putty spattle both to dry and damp lower stratums
- Vapor permeable
- GLIMS® ВодоSTOP Elastic 1K is used before facing with ceramic tiles, porcelain gres, mosaics, natural and artificial stone, as well as plastering or filling-up of surfaces
- GLIMS® ВодоSTOP Elastic 1K is water-based, environmentally friendly
LOWER STRATUM PREPARATION
The lower stratum surface must be durable, free from dust, dirt, paint and grease stains. Before the mastic compound application it is necessary to treat porous, weak and highly absorbent lower stratums with GLIMS® PrimeГрунт primer or moisten them with water. To reduce the mastic compound consumption before GLIMS® ВодоSTOP Elastic 1Kapplying it is necessary to level the surface using GLIMS® Tweed extra-strong plaster (minimum layer thickness is 10 mm) and/or GLIMS® StyroПрайм, GLIMS®Stukko-RF stopping fillers. Horizontal surfaces with irregularities of 5 mm or more are recommended to be preliminarily (at least 24 hours earlier) leveled with GLIMS®CF-10 and GLIMS®CF-40 cement poured floors.
INSTRUCTIONS FOR USE
GLIMS® Water STOP Elastic 1Kis applied with a brush, roller or putty spattle in at least two layers with intermediate drying for at least 2 hours. The material must be mixed before use. Each subsequent layer is applied after the complete drying out of the previous one. When applying GLIMS®ВодоSTOP Elastic 1K the temperature of the lower stratum and the environment should not be lower than +5 ° C and not higher than +35°C. The recommended material consumption per 1 layer is 400-650 g/m². For weak and highly water-absorbing lower stratums: after their preliminary damping, at first a thin primer layer of the material (about 200 g/m²) is applied on the wet surface. Then, after it has complete drying out (not earlier than after 2 hours), a second layer is applied, if necessary, a third layer of material is also applied. If visible defects remain on the dried surface of the material, an additional coat of GLIMS® ВодоSTOP Elastic 1K should be applied. At this, the consumption for the walls treatment is not less than 800 g/m², for the floor treatment - not less than 900 g/m². Areas of the most likely formation of cracks (for example, junctions between walls and floors, hairline joints of slabs, pipes, wires, etc.) are recommended to be treated with three layers of mastic compound using a fiberglass mesh. It is also recommended to use a fiberglass mesh for waterproofing gypsum boards, moisture-resistant gypsum board, gypsum plasterboard at the sheets hairline joints. Each subsequent layer of mastic compound is applied in the direction perpendicular to the previous one. It is possible to glue the tiles, apply the plaster or stopping filler on the surface of GLIMS® ВодоSTOP Elastic 1K after the material drying out, i.e. not earlier than 2,5 hours from the moment of the last layer applying (at a temperature above +22°С and humidity not more than 50%). Avoid exposure to water during the drying period. At elevated temperatures the final drying is faster. The waterproofing properties, strength and adhesion of the material gains after complete drying out. Operation temperature range is from -50 to +70 ° С. The material is not recommended for use as a topcoat.
CONSUMPTION
0,8-1,3 kg of mastic compound per 1 m2.
PACKAGING
pails of 4, 14 kg
TRANSPORTATION AND STORAGE
Transport and store in conditions ensuring the integrity of the packaging, at a temperature from +5 to +30°C. protect from frost and direct exposure to sunlight. The warranty storage period is 12 months from the date of production. Complies with European standards EN 14891 (Class DM P)
PRODUCT DISPOSAL
The waterproofing material should be disposed as building waste. It is forbidden to throw materials into the sanitary piping. The plastic pail should be disposed as household garbage. TU 5775-009-40397319-2015 № Г-9018
