glims aнглийская версия
Интернет-магазин представительского класса
Catalogue
Tile adhesive
Plasters
Flooring compounds
Primers
Repair mortars
Waterproofing materials
About company
Contacts
+7 (499) 115-07-93
Request a call
Ask a Question
Войти
  • Корзина0
  • Отложенные0
info@glims.tetris-studio.ru
г. Москва, ул. Пушкина 19
  • Instagram
glims aнглийская версия
RU
/
EN
+7 (499) 115-07-93
Request a call
Catalogue
  • Tile adhesive
    Tile adhesive
  • Plasters
    Plasters
  • Flooring compounds
    Flooring compounds
  • Primers
    Primers
  • Repair mortars
    Repair mortars
  • Waterproofing materials
    Waterproofing materials
About company
  • Contacts
+  ЕЩЕ
    glims aнглийская версия
    Catalogue
    • Tile adhesive
      Tile adhesive
    • Plasters
      Plasters
    • Flooring compounds
      Flooring compounds
    • Primers
      Primers
    • Repair mortars
      Repair mortars
    • Waterproofing materials
      Waterproofing materials
    About company
    • Contacts
    +  ЕЩЕ
      Отложенные 0 Корзина 0
      glims aнглийская версия
      Отложенные 0 Корзина 0
      Phones
      +7 (499) 115-07-93
      Заказать звонок
      • Catalogue
        • Back
        • Catalogue
        • Tile adhesive
        • Plasters
        • Flooring compounds
        • Primers
        • Repair mortars
        • Waterproofing materials
      • About company
        • Back
        • About company
        • Contacts
      • Личный кабинет
      • Корзина0
      • Отложенные0
      • +7 (499) 115-07-93
      Contact Information
      г. Москва, ул. Пушкина 19
      info@glims.tetris-studio.ru
      • Instagram

      GLIMS®CRF-40 Complies with GOST R 56378-2015 (class R3) Repair composition of poured type

      Home
      —
      Repair mortars
      Tile adhesivePlastersFlooring compoundsPrimersWaterproofing materials
      —GLIMS®CRF-40 Complies with GOST R 56378-2015 (class R3) Repair composition of poured type
      GLIMS®CRF-40 Complies with GOST R 56378-2015 (class R3) Repair composition of poured type
      750 rub./pcs.
      Price Options
      750 rub./pcs.
      Details
      Out of stock
      Описание

      Non-shrink repair composition on small-grained gritter of poured type containing polymer fibre. It is used with a destruction depth from 15 to 40 mm on horizontal lower stratums and surfaces with a gradient of not more than 4% (per 1 meter).

      APPLICATION DOMAIN

      Civil construction:

      • repair of steps and stair flights;
      • repairing of hand railings mounting defects; poles, fences, barriers installation and fixing in the soil or concrete;
      • packing voids under foundations, walls, load carrying structures;
      • strengthening of horizontal concrete and stone lower stratums;
      • repair of voids and caverns in concrete, stone, brick walls;
      • repair of access trestles in garages and parking lots;
      • repair of the upper part of slab roofs and floor slab panels;
      • repairing of horizontal coursings, spalls of paving slabs, cracks with a width of more than 5 mm.

      Industrial construction:

      • repair of road and bridges pavement, airport runways, decks, concrete surfacing of parking areas, etc., - in any climatic conditions and taking into account high mechanical loads;
      • repair of industrial floorings, equipment foundations - in premises and in open areas stressing high mechanical loads and exposed to aggressive environments (mineral oils, greases, etc.);
      • repair of concrete and reinforced concrete structures that are operated in sea and fresh water conditions;
      • repair of reinforced concrete supports exposed to high permanent and dynamic loads;
      • protection of concrete from aggressive waters containing sulfates, sulfides, chlorides, thawing chemicals;
      • joint grouting, rigid connection of precast structures;
      • cracked rock grouting;
      • consolidation of the bases and foundations.
      SURFACE PREPARATION

      It is applied to horizontal concrete lower stratums with a gradient of not more than 4% (per 1 meter), from the surface of which previously it is necessary to remove cement slurry, loose coating, the remains of old coatings, paints, etc. To perform these works, the use of a milling machine is recommended. Before the mortar mix applying to the surface to be repaired, it is necessary to eliminate active leakages using the rapid-hardening, expanding GLIMS®ГидроПломба repair composition. If the reinforcement is open and has instances of corrosion, it must be cleaned of rust and dirt, and then treated with a corrosion-preventive compound. Before the repair mortar applying, the surface of the lower stratum must be supplied with clean water up to a full saturation level. Thickness of application in one layer is from 15 to 40 mm. If the depth of the repaired area exceeds 40 mm, then the application work must be performed in two stages, at this fasten the metal mesh before the first layer applying, leaving a space between the mesh and the surface of at least 10 mm. If the lower stratum is not strong enough, after the reinforcement mounting it is necessary to treat the repaired area with Glims®PrimeГрунт. When material applying and hardening the temperature of the lower stratum and the environment should not be lower than +5 ° C. For more information refer to the coating laying flow diagram.

      MORTAR PREPARATION

      Pour the package contents into a reservoir with clean water at a rate of 0.12-0.14 l of water per 1 kg of dry mix (3-3,5 l per bag of 25 kg) and mix thoroughly with a mixer machine to even consistency. Keep the mortar for 2-3 minutes and mix it once more.

      TECHNOLOGY OF WORK EXECUTION

      The ready for use mortar mix should be applied using special equipment (for example, for air placing) or manually. The mortar mix pouring is performed continuously - from one side of the defective area to the other. This is necessary to prevent air entering and void formation in the mortar mix. Mortar mix pouring from two opposite sides is not allowed. To ensure optimal applied mortar mix solidification conditions it is necessary to protect its top layer from water evaporation using a polymer film or to moisten the surface with finely sprayed cold water for 24 hours (48 hours in hot and windy weather). Solidification time and subsequent finishing to a greater extent are dependent on environmental conditions. Operation temperature range – from -50 to +70 ° С. While working it is necessary to observe the norms of SNiP and industrial hygiene. The material is environmentally friendly in use and operation.

      CONSUMPTION:

      2,1 kg/m² with a layer thickness of 1 mm.

      TRANSPORTATION AND STORAGE

      During transportation and storage, bags with dry mortar should be protected from damage and soaking. The storage period is 12 months. Complies with GOST R 56378-2015 (class R3)

      750 rub./pcs.
      Price Options
      750 rub./pcs.
      Details
      Out of stock
      Do you need a consultation?

      Our specialists will answer any question you are interested in!
      Ask a question
      Catalogue
      About company
      Contacts
      +7 (499) 115-07-93
      info@glims.tetris-studio.ru
      г. Москва, ул. Пушкина 19
      • Instagram
      2025 © Аспро: Максимум - интернет-магазин